EFTA02520550.pdf

From: Jeffrey Epstein <[email protected]> Sent: Thursday, August 29, 2013 10:37 PM To: Eric Roth Subject: Re: ledge and side panel profile they will be installed most of the time On Thu, Aug 29, 2013 a= 5:57 PM, Eric Roth < mailto=1.> wrote: If you are going t= keep the two seats installed most of the time in the aft area (across fro= the berthing divan), then I would do the same detail in that ledge. If you are not going to keep the=two seats installed in the aft, then I would let ledge remain all wood.=/u> My thought is that with the two =eats removed, it will draw attention to the fact that the seats are not in=talled. Your thoughts? ERIC H. ROTH I PRESIDENT F :te IC <tel <http://www.facebook.com/in=ljet> 2221Smithtown Avenue, Lon= Island MacArthur Airport, Ronkonkoma, New York 11779qp EFTA_R1_01657394 EFTA02520550  From: Jeffrey =pstein Imailto:[email protected] <mailto:[email protected]> I Sent: Thursday, August 29, 2013 5:35 PM To: Eric Roth <=>Subject: Re: ledge and side panel profile =k. =u> On Thu, Aug 29, 2013 at 5:21PM, Eri= Roth <ERoth@int=jet.com <mailto:[email protected]» wrote: Jeffrey,</=> =u> Just got out of a meeting wher= we all discussed what would look best and they agreed with me.<=u> My strong opinion is it should b= leather- The only thing that could bag th=s edge is the seat - leather to leather. If you are worried about bangi=g, the leather to leather would protect the seat better than a hard, unfor=iving material like wood or metal. It will coordinate with the co=ference table detail Metal in that area will be too much. You already have 2 =etal cup holders and metal switches. More metal will turn a detail acce=t into a focal point. Matching the hardwood(color an= grain) that run length is going to look a bit piece mealed.=u> I really believe that the detail=in the leather to coordinate with the conference table is the way to go...= ERIC H. ROTH I PRESIDENT 2 EFTA_R1_01657395 EFTA02520551  P a> C<te /a> I <tel <mailto: I </=pan> www.intljet.com <http://www.intljet.com/> <http://twitter.comMintket> 2221Smithtown Avenue, Lon= Island MacArthur Airport, Ronkonkoma, New York 11779=/p From: Jeffrey =pstein Imailto:[email protected] <mailto:[email protected]> I Sent: Thursday, August 29, 2013 4:38 PM To: Eric Roth; Ivjrt Subject: Re: ledge and side panel profile=/p> why not in wood? or brushed, ? im concerned about dirt and banged up =ooking On Thu, Aug=29, 2013 at 4:33 PM, Eric Roth c <mailtol > wrote: Jeffrey,</=> The attached drawing illustrates the look=that will allow us to keep the seats as is and gains you 2" of aisle cle=rance between the seats inn the fwd club area. I think it will look great and compliment the new conf=rence table detail. Your thoughts... ERIC H. ROTH I PRESIDENT 3 EFTA_R1_01657396 EFTA02520552  =U> P <= href="tel:631.737.5900" tar et=" blank" ="tel target="_blank" mailto: I www.intljet.com c=span> <http://twitter.com/Wintljet> <=u> 2221S=ithtown Avenue, Long Island MacArthur Airport, Ronkonkoma, New York 11779<=span> <=div> ******** **•**= The information contained=in this communication is confidential, may be attorney-client privilege=, may constitute inside information, and is intended only for the use of the a=dressee. It is the property of Jeffrey Epstein Unauthorized use, di=closure or copying of this communication or any part thereof is strictl= prohibited and may be unlawful. If you have received this communication in error, p=ease notify us immediately by return e-mail or by e-mail to [email protected], =nd destroy this communication and all copies thereof, including all attachm=nts. copyright -all rights reserved The information contained in this communication is confidential, may be =ttorney-client privileged, may constitute inside information, and is in=ended only for the use of the addressee. It is the property of Jeffr=y Epstein Unauthorized use, disclosure or copying of this communication or any par= thereof is strictly prohibited and may be unlawful. If you have receiv=d this communication in error, please notify us immediately by retur= e-mail or by e-mail to [email protected] <[email protected]> , and destroy this communication and all copies thereof, including all attachm=nts. copyright -all rights reserved 4 EFTA_R1_01657397 EFTA02520553