EFTA00603443.pdf

Model 1044C-54 Series II TELEHANDLER Axles Accessories & Options Full-time planetary 4-wheel drive. Rated Capacity Oscillating rear axle. Enclosed Cab 10.000 lb14,536 kg) Service Brakes Second Auxiliary Hydraulic Line Maximum Lift Height Hydraulically actuated inboard wet else brakes. Work Lights 54 ft 116.5 ml Parking Brakes Road Lights Frame Leveling Spring applied hydraulic release brake with 10 degrees transmission declutch feature. Rotating Beacon Lift Speed (boom retracted, no load) Tire Options Tires Foam-filled Up: 15.6 sec Standard: Hydro fill 14.00 x 24 —12 ply Down: 14.6 sec Rack Cab Solid Boom Speed (no load) Extend: 15.2 sec Certified ROPS/FOPS structure. Retract: 11.3 sec Suspension seat Attachments Travel Speed Forward Steering wheel mounted horn. 22 m0135 kmph) max. Rear view mirrors. Standard Carriage Drawbar Pull (loaded) 50 in. (1.3 m) or 60 in. 11.2 m) or 72 in. 11.B m) 21.700 lb (9,843 kgl Steering Side Tilt Carriage 4-wheel circle, 4-wheel crab, 2-wheel front. 50 in. (1.3 m) or 60 in. 11.2 m) or 72 in. 11.B m) Operating Weight With Carriage and Forks 32.697 lb (14.931 kg) Instruments Swing Carriage Forward Reach Hydraulic ail temperature, fuel level, 72 in. (1 90 degrees 45 ft113.7 m) tachometer, and hourmeter gauges. Sheet Material Adapter Horizontal Load Placement Warring indicators for transmission Tower 80 in. (2.0 nil oil temperature, hydraulic oil temperature. 8 ft 12.4 ml. 50 in. (1.3 ml Standard or engine oil pressure, alternator charging, Side Tilt Carriage air filter restriction, hydratiic oil filter Standard Specifications restriction, and low brake pressure. Pallet Forks Indicators for parking brake and 2.36 x4 x48 in.160 mmx 102 mm x 1.2m) Engine MS System. 2.36 x 5x 48 in. 160mm x 127mm x 1.2 m) Make and Model John Deere 4045TF 2.00 x6 x 72 in.(51 mm x 152 mm x 1.8ml Fuel No. 2 Diesel Controls Cycles 4 Multi-function, fully proportional pilot Lumber Forks No. of Cylinders 4 operated joystick controls for boom 1.75 x 7 x 60 in. (44 mm x 178 mm x 1.2 ml Displacement 276w in (4.5 L) functions, carriage tilt auxiliary control, 2.36 x6 x 60 in.160 mmx 152mm x 1.5 ml Rated Speed 2,500 rpm frame leveling, and horizontal load placement system. Cubing Forks Max. Gross BHP 115 hp(85 kW) 2x 2 x 48in.(51 mm x 51 mmx 1.2 m) Fuel Tank 36 gal (136 LI Hydraulic System Engine Block Heater Load sensing dual gear pumps. Material Bucket Engine Filters 72 in. (1.8 m), 1.0 cu yd110.76 m31 33.5 gal (12711 system capacity. 96 in. (2.4 m), 1.5 cu yd (1.15 m31 Two-stage dry air cleaner — centrifugal pre-cleaner with continuous dust ejector Front Outriggers 102 in.12.6 m,12.0 cu yd 11.53 m3) plus replaceable primary dry filter element Axle mounted high clearance outriggers Grapple Bucket and safety element. allow frame leveling without changing 96 in. (2.4 ml, 1.75 cu yd11.34 m3) Visual service indicator. stance. Truss Boom Replaceable spin-on fuel filter. Full-flew Auxiliary Hydraulics 12 ft 13.7 ml, 2,000 lb (907 NI capacity replaceable spin-on engine oil filter. Used for all attachments equipped with cylinders or other hydraulic components. 15 ft (4.6 m), 2,000 lb (907 kg) capacity Electrical System Consists of valves, controls and 12 ft 13.7 m)with winch, 2,000 lb Voltage: 12V hydratiic lines. (907 kgl capacity Alternator: 95 amp Fork Mounted Work Platform Battery: 925 cold cracking amps at 0'F 8 ft 12.4 rah 1.000 lb (455 kgl capacity Transmission Lifting Hook Modulated powerstifI. 4-speed forward and 3-speed reverse. EFTA00603443  Model 1044C-54 Series II TELEHANDLER aat OR MR nit 1811 2411 [OR LL 11 I2R IR It In 10f0133 f0RIV2M • IMICARS IEM ' OSOUJOGILO(IC Length (less forks 246 in. 16.24 ml • %flotsam Width 101 in. 12.57 ml 4881148111 Height 97 in. 12.46 ml Wheelbase 124 in. (3.14 ml MRIWM Ground Clearance 16 in. (406 mml 40R111Snl Outside Turring Radius 170 in. 14.32 ml M /1111.1•1 Maximum Reach from Front Tires to 24 in.1609 mm) Load Center 45 ft (13.7 ml Valle M 2111tOL5 30' amanita 201,111M 20' 1611(14-9 L38(17.11 10' 811124 M 2 4e11.: 111 a 0 M:111 0' Il 41:11.4•1 IMPORTANT Hated cif t capacities shown are with machine equipped with carriage and pallet forks. The machine must be level on a firm surface with undamaged. properly inflated ties. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths. (If specifications are critical, the proposed application should be discussed with your dealer.) 00 NOT exceed rated lift capacity loads, as unstable and dangerous machine conditions wit result. 00 NOT tip the machine forward to determine the allowable load. Use only JLG approved attachments with proper material handler model/attachment load capacity charts displayed in the operators cab. OSHA requires all rough terrain forklift operators be trained according to OSHA 29 CFR 1910178 (1). JLG Industries, Inc. 1 JLG Drive McConnellsburg. M 172339533 Due to contimous product improvements, JLG Industries reserves the right to make specification and/or equipment changes form No.: SS-1.1044C-S4.0405-10M without prior notificati3n.lhismachire meets Part No.: 3132504 or exceeds ASME 656.62005 as originally 8071006 manufactured for intended applications. Printed in USA An Oshkosh Corporabon Company EFTA00603444