EFTA02397249.pdf

From: Ann Rodriquez Sent: Monday, April 13, 2015 6:47 PM To: jeffrey E. Subject: Fwd: Barge List Ann R. Begin forwarded m=ssage: From: Bill Hague &=t <=>Date: April 13, 2015 at 2:29:56 PM AST To: ann rodri uez Cc: Rich Kahn Da hne Wallace , Gene Kral u : e: G=rge Us Ok.=nbsp; 1 Rudders must be rem=ved and the lower portion must be renewed to proper dimension. They are wor= to the point of failure and vibrate badly. 2= We bought pumps and pulleys we can install but I a= referencing the gear in the aft compartment that is the hydraulic actuator=and linkage for the rudders 3 &nb=p;The cylinders were damaged at sea due to improper installation and subseq=ent damage from a broken fitting. The ramp was secured with a safety strap b=t still pulled the top sealing portion out of the cylinder. The fit o= the mounts needs to be remedied at this time. The cylinders work now but a=e not repairable. Evaluation while being removed to correct and improve the=mounting is necessary at a minimum. 4 =div> The exhaust was assembled without funding to get the barge=off the dick at the last haulout. It is not properly assembled or supports n=r is it insulated. 6 =e have new ones but need new mounting hoses And must be done out o= the water 7 Bearings must be pur=hased. I think SBDD has them EFTA_R1_01430244 EFTA02397249  8 &n=sp; Inspection and new sacrificial sinks installed. 9 SBDD should provide this but it can be discussed.&=bsp; 10 Machine shop work&n=sp; SBDD 12 This s=ould be done at the same time the tank is cleaned. 13 Watertight compartments forward would need to be d=watered if breached. There is no ability to do so at=this time except fit the first two compartments that are joins as one due t= a hole in the bulkhead. 16 =The gauges for oil and temp and rpm are not accurate. One over temperature a=arm is not working as well. 18 &nb=p; Parts.... As needed by inspection. </=iv> Sent from my iPhone > wrote: Hey Boscoe, Please see questions ----? I need a clear understanding of the=listed items, What parts should we purchase and What can be done i= house. 1. Rudders. What should be done? = 2. Steering Gear. Did we buy the parts for this? 3. Hydraulic Cy=inders. What need to be done? 4. Exhaust system: What are the=issues? 5. Engine Mounts and alignment. (Ok!) 6. Stuffing boxes/=eals. Install new units: Should we buy the new units? 7. Cutlass be=rings. Do we need to purchase? 8. Engine Cooling Grid Coolers and Z=nks. What need to be done? 9. Bottom Paint and Barrier Coat/ Hull Z=nks. Should we purchase? 10. Engine and marine gear control bracke= work. Do we need to purchase? 2 EFTA_R1_01430245 EFTA02397250  11. Fuel tank clean out. Port and s=arboard. (Ok!) 12. Starboard deck fuel fill adapter replacement. Should we replace or fix? 13. Bilge pumping system forward compartme=ts. What about the forward compartments? 14. Repair existing 24 vo=t alternator and add a second one to port motor. Should we purchase? <=r>1.S. Inspect and size all hydraulic lines and fittings as needed. (Ok!) 17. Install engine room lighting. (Ok!) 18. Tune and s=rvice both engines and marine gear. ----- Any parts need? 19. Clea= and paint engine room. (Ok!) DISCLAIMER: The information contained in this e-mail may be privileged,=onfidential, and protected from disclosure. If you are not the intended rec=pient, you are hereby notified that any dissemination, distribution or dupl=cation of this communication is strictly prohibited. If you have received t=is communication in error, please notify the sender immediately On Monday, April 13, 2015 12:22 PM, Boscoe wrote: The following is the list I discussed with Gene at Subbase=Drydock today 4/13/2015. He is familiar with it and is now submi=ted for your review. l=spect and Repair the following; 1. Rudders. 2. Steering Gear. 3.=Hydraulic Cylinders. 4. Exhaust system 5. Engine Mounts and alignmen= 6. Stuffing boxes/seals.. Install new units 7. Cutlass bearin=s 8. Engine Cooling Grid Coolers and Zinks 9. Bottom Paint and Barrie= Coat/ Hull Zinks 10. Engine and marine gear control bracket work. 1=. Fuel tank clean out. Port and starboard 12. Starboard deck fuel fill a=apter replacement 13. Bilge pumping system forward compartments 14. R=pair existing 24 volt alternator and add a second one to port motor. 15= Inspect and size all hydraulic lines and fittings as needed. 16. Engin= and marine gear instruments in control tower 17. Install engine room li=hting 18. Tune and service both engines and marine gear. 19. Clean a=d paint engine room. Timing of work I have been told&n=sp; this haul out must be done in late April or May as there is scheduled a=d contracted work reported for this facility during June, July and August. <=r> Please, respond with any questions you may have. 3 EFTA_R1_01430246 EFTA02397251 =/div> 4 EFTA_R1_01430247 EFTA02397252