EFTA00849536.pdf

From: "Jeffrey E." <[email protected]> To: LAllenby Subject: Re: LSJ Plate Work Date: Mon, 03 Aug 2015 14:08:40 +0000 Yes On Mon, Aug 3, 2015 at 9:59 AM, LAllenby < > wrote: Yes, I discussed this with Gene at length and this is our only option. Can they proceed? Leighton Allenby Director of Pro erties On Aug 3, 2015, at 9:39 AM, jeffrey E. <[email protected]> wrote: is that what you are reccomending? On Mon, Aug 3, 2015 at 9:38 AM, LAllenby < > wrote: Good Morning Anna- Upon reviewing and inspecting the inside of the compartments, forward of the engine room, we have come up with a quotation for repairing all the "wasted" plate. Approximately 160 square feet of plate has to be cut out and replaced. The square footage equals 848LBS x $45 per pound the total would be $38,160 (This price includes all labor and material). We will also have to remove both keel coolers due to their location with the plate that has to be cut out. We will also have to fabricate two new boxes in which they sit and then remount these boxes once the new plate is welded into place. The price for this is $5850 includes labor and material. Two water tight bulkheads are also compromised and several areas will need to be "cropped" out and replaced. Labor and materials is $3380. We will also "plug weld" 12 more additional areas that have deteriorated and need to be addressed. These two compartments have been inspected by both Gabriel, the project manager, and Bosco. In addition, the emergency bilge pump system needs to be renewed and it is our recommendation to have Bosco undertake this job. Please note that we have not charged any additional lay days and will continue not to. The areas that need to be cut out and replaced are very confined and difficult to work in. With the savings on lay days it is over $3500 so we will not be able to move on our final quotation. I have also attached a few pictures EFTA00849536  Total for labor and material $47,390 Leighton Allenby Director of Properties On Aug 3, 2015, at 9:21 AM, jeffrey E. <[email protected]> wrote: that is only the problem„ is there a proposal for solution, ? please try to add action steps to issues, telling me only that there is a problem is time consumig On Mon, Aug 3, 2015 at 9:13 AM, LAllenby I> wrote: The hull is compromised - rusted through in areas on his map. Leighton Allenby Director of Properties On Aug 3, 2015, at 9:09 AM, Richard Kahn c lia> wrote: Bosco email off point. Disappointed with bosco on every step of this barge overhaul and concerned he is not best person to care for and operate moving forward. To many surprises and then an excuse and disclaimer each time. As I am sure you will say we have no choice I wanted to confirm we shall proceed with latest Change order for 47,390 Please advise Thank you Sent from my iPhone Begin forwarded message: From: Leighton Allenby <I Date: July 31, 2015 at 3:49:39 PM EDT To: Richard Kahn Subject: Fwd: LSJ Plate Work FYI Leighton Allenby Director of Pro erties EFTA00849537  Forwarded message From: Bill Hague Date: Fri, Jul 31, 2015 at 3:09 PM Subject: RE: LSJ Plate Work To: Understood. Gabe, one of his hands and I went over all the remaining cavities/compartments and found only a half dozen minor and repairable spots in the hull plating. The bulkheads show staggered severe pits/holes that also can be dealt with reasonably. I agree about the surveyor. Also, your email ended up in my junk mail. I have added you to my contacts to avoid that in the future. I regret the delay in responding. For your information, I contacted a Navy colleague and asked for the present contractors information concerning construction of the latest Navy LCM8's I did this to quantify your question about replacement costs of the Barge. I was Refered to Kvichak Marine in Seattle. Art Parker there said my guess of 2 million is likely low. A build that heavy is likely a 3 to 4 million dollar job in his opinion. His company is bidding on the Caiman design 60 and 70 for the USN. Good Day Boscoe From: Date: Fri, 31 Jul 2015 12:22:37 -0400 Subject: Re: LSJ Plate Work To: [email protected]; I CC: Hello Anna and Boscoe, Can you please go over every inch of Big D and determine when the bleeding to Mr. Epstein is going to stop. I know I am coming in late in the last quarter but there should have been a survey recommended so this additional work outside of the original budget did't occur and a 10 to 15% mic added for unforeseen. I see no other option but to recommend to Mr. Epstein and Richard that this work be completed. Please thank Gabriel for the savings on the lay days Mr. Epstein and Richard, I this additional $47,390 expenditure approved? Best, Leighton Good Morning Anna- Upon reviewing and inspecting the inside of the compartments, forward of the engine room, we have come up with a quotation for repairing all the "wasted" plate. Approximately 160 square feet of plate has to be cut out and replaced. The square footage equals 848LBS x $45 per pound the total would be $38,160 (This price includes all labor and material). We will also have to remove both keel EFTA00849538 coolers due to their location with the plate that has to be cut out. We will also have to fabricate two new boxes in which they sit and then remount these boxes once the new plate is welded into place. The price for this is $5850 includes labor and material. Two water tight bulkheads are also compromised and several areas will need to be "cropped" out and replaced. Labor and materials is $3380. We will also "plug weld" 12 more additional areas that have deteriorated and need to be addressed. These two compartments have been inspected by both Gabriel, the project manager, and Bosco. In addition, the emergency bilge pump system needs to be renewed and it is our recommendation to have Bosco undertake this job. Please note that we have not charged any additional lay days and will continue not to. The areas that need to be cut out and replaced are very confined and difficult to work in. With the savings on lay days it is over $3500 so we will not be able to move on our final quotation. I have also attached a few pictures Total for labor and material $47,390 Leighton Allenby Director of Properties On Fri, Jul 31, 2015 at 11:43 AM, Ann Rodriquez - wrote: Ann R. Begin forwarded message: From: gene kral Date: July 31, 2015 at 11:19:19 AM AST To: Ann Rodriquez Subject: Fw: LSJ Plate Work Reply-To: gene kral Good Morning Anna- Upon reviewing and inspecting the inside of the compartments, forward of the engine room, we have come up with a quotation for repairing all the "wasted" plate. Approximately 160 square feet of plate has to be cut out and replaced. The square footage equals 848LBS x $45 per pound the total would be $38,160 (This price includes all labor and material). We will also have to remove both keel coolers due to their location with the plate that has to be cut out. We will also have to fabricate two new boxes in which they sit and then remount these boxes once the new plate is welded into place. The price for this is $5850 includes labor and material. Two water tight bulkheads are also compromised and several areas will need to be "cropped" out and replaced. Labor and materials is $3380. We will also "plug weld" 12 more additional areas that have deteriorated and need to be addressed. These two compartments have been inspected by both Gabriel, the project manager, and Bosco. In addition, the emergency bilge pump system needs to be renewed and it is our recommendation to have Bosco undertake this job. Please note that we have not charged any additional lay days and will continue not to. The areas that need to be cut out and replaced are very confined and difficult to work in. With the savings on lay days it is over $3500 so we will not be able to move on our final quotation. I have also attached a few pictures Total for labor and material $47,390 EFTA00849539 <resized2jpg> <resized5jpg> <resized7jpg><resized8jpg> EFTA00849540 <resized10.jpg> <resized12.jpg> <resized8.jpg> <resized.2.jpg> <resized5.jpg> <resized7.jpg> <resized 1 2.jpg> EFTA00849541  <resized I 0.jpg> please note The information contained in this communication is confidential, may be attorney-client privileged, may constitute inside information, and is intended only for the use of the addressee. It is the property of JEE Unauthorized use, disclosure or copying of this communication or any part thereof is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by return e-mail or by e-mail to [email protected], and destroy this communication and all copies thereof, including all attachments. copyright -all rights reserved please note The information contained in this communication is confidential, may be attorney-client privileged, may constitute inside information, and is intended only for the use of the addressee. It is the property of JEE Unauthorized use, disclosure or copying of this communication or any part thereof is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by return e-mail or by e-mail to jeevacation®gmail.com, and destroy this communication and all copies thereof, including all attachments. copyright -all rights reserved please note The information contained in this communication is confidential, may be attorney-client privileged, may constitute inside information, and is intended only for the use of the addressee. It is the property of JEE Unauthorized use, disclosure or copying of this communication or any part thereof is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by EFTA00849542 return e-mail or by e-mail to [email protected], and destroy this communication and all copies thereof, including all attachments. copyright -all rights reserved EFTA00849543