EFTA00695796.pdf

From: Larry Visoski To: [email protected] Subject: LSJ line array speakers Date: Sat, 06 Jul 2013 13:14:22 +0000 Jeffrey, My research found this line of outdoor, water/resistant speakers. These are Line Array outdoor deign, however its recommended the speakers should be protected from elements, Guitar Center carries this line, i will obtain pricing if you think this is speaker system you are thinking? Web link. httn://www.qscaudio.com/products/speakers/widelinewideline wx.htin Do you like this deign ? Thx, Larry Products / Loudspeakers / Line Array Systems LINE ARRAY SYSTEMS WLWX Weatherized WideLine Systems ILA Installation Line Array WideLine-wx models are constructed using premium birch plywood which is full WideLine-1Q encapsulated in fiberglass. The input connector plate is replaced by a hardwired, captive, UV WideLine-8 resistant, outdoor-rated (direct burial) cable with a gland-nut through the cabinet for Weatherized WideLine waterproofing. The cable will be 3 meters in length unless otherwise specified at the time the Systems order is placed. Grilles are stainless steel covered in outdoor rated, vinyl coating and lined with acoustic foam and a fine woven stainless steel mesh. WideLine WX models are strictly built to order. Please allow 90 days plus shipping DOCUMENTS time from the time the P.O. is delivered to QSC for delivery. User Manual (FIE=25212)_ RELATED PRODUCTS WL2102-wx The WL2 I 02-wx is a weather WiddinrainincAnay_Systrim resistant, installation version of the Widdinataincitaay_Systcm WideLine-I0 WL2102-w line array. siF)18-sw Subwoofez All rigging hardware is removed and WL2l8-sw WideLine Subwoofer replaced with four female MI0 fittings SC28 System Controller (eight total) mounted to either end of PSControl net BASIS the enclosure. The loudspeaker is designed for 3-way operation only and IMPORTANT NOTE: no handles are provided. An adjustable, external, bolt-on rigging Si;nal Processing system for box-to-box connection and Requirements adjustment of splay angles is included. The AF2102-wx is a compatible, WL2102-wx WL3082-wx Like most line-array systems aluminum array frame for use when available today, QSC WideLine suspending the WL2102-wx. Array and ILA line-arrays require frames for the standard WL2102-w are carefully optimized signal not compatible with the WL2102-wx. processing in order to perform as intended. QSC has developed processing settings for these WL3082-wx loudspeaker systems using our The WL3082-wx is a weather SC28, BASIS and Q-Sys digital resistant, installation version of the processing devices. Arriving at WideLine-8 WL3082 line array. All these settings requires skilled rigging hardware is removed and GP218-wx engineers, sophisticated replaced with four female MI0 fittings measurement equipment and (eight total) mounted to either end of repeated listening in various EFTA00695796  the enclosure. The loudspeaker is environments. designed for 3-way operation only. An adjustable, external, bolt-on rigging It is not possible to simply take system for box-to-box connection and adjustment of splay angles is included. The AF3082- the parameters from a QSC wx is a compatible, aluminum array frame for use when suspending the WL3082-wx. Array processor, transfer them to frames for the standard WL3802 are not compatible with the WL3082-wx. another processor and get the same results. Other processor manufacturers use different GP218-wx algorithms and design The GP218-wx is a weather resistant, installation version of the WideLine-10 GP2I8 techniques that will produce a subwoofer. The standard version includes no suspension provisions but M10 suspension different transfer function even points may be added on request. if the settings are substantially the same. As a result, QSC is unable to provide settings or Weatherized WideLine tuning support for our line array SPECIFICATIONS WL2102-wx WL3082-wx GP218-wx systems when used with any processors other than those System Type Tri-amp line array Tri-amp line array 2 x 18" vented specified by QSC. element element subwoofer Transducers High-frequency 3" titanium 3" titanium diaphragm, diaphragm, Low-frequency neodymium magnet neodymium magnet 2 x 18" transducers, 2 x 10" transducer, Dual, 8" woofer, 4" voice coil, ceramic 3" voice coil, ferrite 2.5" voice coil magnet magnet Frequency Response 55 Hz- 18 kHz 68 Hz- 18 kHz 31.4 Hz - 240 Hz (+.3 dB) (without processing) Frequency Range 48 Hz - 20 kHz 62 Hz - 20 kHz 27.4 Hz - 1.2 kHz (-10 dB) (without processing) Continuous Power HF: 80 W HF: 85 W Capacity' LF/MF: 600 W LF/MF: 250 W LF: 1700 W Peak Output 2 HF: 127 dB HF: 122 dB LF: 133 dB LF: 128 dB LF: 140.7 dB Nominal Coverage H: 140° H: 140° V: dependent on V: dependent on number of elements number of elements used used Input Connectors Tinned, bare wire Tinned, bare wire Tinned, bare wire Suspension / Integral rigging Integral rigging None (MI0 points Attachment Points system, vertical splay system, vertical available by request) adjustable splay adjustable in I° increments in 1° increments from 0*-10° from 0°-10° Weight (Net) 92.5 lb (42 kg) 61 lb (27.7 kg) 215 lb (97.5 kg) Dimensions (HWD) 11.75" x 27.25" x 21.13" x 30.13" x 9.5" x 20" x 15.5" 18.5" 47.32" 241 mm x 508 mm x 298 mm x 692 mm x 537 mm x 765 mm x 394 mm 470 mm 1202 mm 2 Continuous !EC specified test signal, 2 hours bi-amp mode unless otherwise stated. 2 Calculated at I m usingpower capacity and system sensitivity 6 dB peak-to-average signal ratio assumed. Specifications subject to change without notice. Sent from my iPad EFTA00695797